Bosch Gen 2 Service Parts Archives - eBike Motor Centre (Performance Line Bearings)

Bosch Gen 2 Left hand bearing shield kit. Part No PLB00536

Peter Collard — Thu, 17 Nov 2022 10:04:13 +0000

This kit contains a stainless steel shield washer and a thinner 1.5mm circlip to replace the original 2mm clip.

The left hand crankshaft bearing should be covered with Bosch Long Life “Tacky” Grease then the shield washer placed over the outer bearing seal. The grease should be checked from time to time, depending on your riding terrain, bike cleaning habits, weather conditions etc.

Generation 2 motor BDU2xx (NOTE: Small chainring shown below)

The post Bosch Gen 2 Left hand bearing shield kit. Part No PLB00536 appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 Motor circlip kit. Part No PLB00534

Peter Collard — Wed, 16 Nov 2022 17:55:03 +0000

If you are overhauling any Bosch Gen 2 motor, this kit contains every circlip used in the motor. These should be replaced to ensure good clip integrity.

Generation 2 motor BDU2xx (NOTE: Small chainring shown below).

The post Bosch Gen 2 Motor circlip kit. Part No PLB00534 appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 damping film kit. Part No PLA00922

Peter Collard — Wed, 16 Nov 2022 17:41:38 +0000

These high density, sticky backed foam pads are fitted to the Bosch Gen 2 motor to cushion between the motor and frame this can stop the motor creaking as it flexes against the frame mount.

Bosch Generation 2 motor BDU2xx (NOTE: Small chainring below).

The post Bosch Gen 2 damping film kit. Part No PLA00922 appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 outer crankshaft circlip 2mm thick Pair Part number PLA00921

stew — Wed, 11 Aug 2021 15:18:52 +0000

Bosch Gen 2 Outer Crankshaft Circlip 2mm PLA00921, these are the two circlips visible on either side of the crankshaft. They are 19.5mm internal diameter and 2mm thick, fitted to the Bosch Gen 2 motor.

Bosch Generation 2 motor BDU2xx (NOTE: Small chainring)

The post Bosch Gen 2 outer crankshaft circlip 2mm thick Pair Part number PLA00921 appeared first on eBike Motor Centre (Performance Line Bearings).

Crankshaft seal for Bosch Gen 2. Total protection for the right-hand crankshaft bearing. Part No PLB00530

stew — Wed, 11 Aug 2021 15:18:31 +0000

This is a durable double lip seal, specifically manufactured to fit the Bosch crankshaft. An effective waterproof barrier for the Bosch right-hand crankshaft bearing.

If fitted with the MudStop bearing seal it makes a formidable barrier against water, mud or dust entering into the bearings of your expensive motor. Click here for instructions:

Seal-instruction

With seal and MudStop fitted below.

Bosch Generation 2 motor BDU2xx below (NOTE: Small chainring)

The post Crankshaft seal for Bosch Gen 2. Total protection for the right-hand crankshaft bearing. Part No PLB00530 appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch motor grease for Gen 1 | Gen 2 | Gen 3 motors

Marc — Wed, 11 Aug 2021 15:18:31 +0000

Bosch drive unit grease for gears and bearings within the motor. This grease should be used for overhauls or re-greasing Bosch Performance Line motors.

The post Bosch motor grease for Gen 1 | Gen 2 | Gen 3 motors appeared first on eBike Motor Centre (Performance Line Bearings).

MudShield “Bosch Gen 2 bearing protection”

Peter Collard — Wed, 11 Aug 2021 15:16:49 +0000

MudStop sealing system was designed by VeloLab to ensure better protection for the vulnerable main motor bearing on the Bosch Active and Performance Line / CX motors.

Unlike the Bosch protection seal, MudStop completely covers the entire main motor bearing and outer casing. This stops water and contamination getting past the cover and entering the bearing.

When used with the custom made crankshaft seal, it makes your motor as protected as it always should have been

Full information and instructions can be found here:

MudStop-instructions

The post MudShield “Bosch Gen 2 bearing protection” appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 | Gen 3 | Gen 4 bearing seal “tacky” grease

Marc — Wed, 11 Aug 2021 15:16:49 +0000

Bosch long life tacky grease for any externally fitted seal or bearing cover. This is an excellent product to greatly increase the life and water integrity of your ebike motor.

This grease should be checked and re-applied on a regular basis depending on your local weather conditions, riding terrain, bike cleaning habits etc.

This grease should NOT be used inside the motor!

The post Bosch Gen 2 | Gen 3 | Gen 4 bearing seal “tacky” grease appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 Drive sprocket O-ring Part No PLB00528

stew — Wed, 11 Aug 2021 15:16:49 +0000

Fits behind the sprocket nut of the Bosch Gen 2 motor.

Bosch Generation 2 motor BDU2xx (NOTE: Small chainring)

The post Bosch Gen 2 Drive sprocket O-ring Part No PLB00528 appeared first on eBike Motor Centre (Performance Line Bearings).

Bosch Gen 2 Crankshaft O-rings (pair) Part No PLB00529

stew — Wed, 11 Aug 2021 15:16:49 +0000

These O-rings sit below the crankshaft bearings to prevent water ingress under the bearing itself.

The post Bosch Gen 2 Crankshaft O-rings (pair) Part No PLB00529 appeared first on eBike Motor Centre (Performance Line Bearings).