This bearing race will fit Brose C, T, TF, S and S-Mag 2.1 and 2.2.
The large drive belt pulley contains a one way sprag clutch bearing and its race. This can become worn or damaged by rust, bearing failure etc. It can also be damaged while trying to remove the bearing itself.
The sprag clutch bearing MUST have a smooth, clean surface and the correct grease or the bearing will fail.
Early Brose C, T, TF motors had no seal covering the right hand crankshaft bearing. This seal is extremely effective at stopping water and dirt entering the bearing and ultimately the motor.
This is also a direct replacement if your Brose S or S-Mag seal is missing, worn or damaged. (For 1.2, 1.3, 2.1 and 2.2 motors)
Once the seal has been fitted over the sprocket carrier it will be pushed down when the chainring spider is re-fitted.
This high quality laser cut gasket will fit Brose S-Mag 2.1 and 2.2 and fits between the motor and the drive belt cover.
Description
Blind plug for the connector for the gear sensor or display.
Description
| Part Number | E22243-200 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 50 Nm |
| Maximum support | 280% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G61340-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 50 Nm |
| Maximum support | 280% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | C97272-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74102-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | E06855-200 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2 A/12 V = 24 W Rear lamp 0,2 A/12 V = 2,4 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74105-xxx |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2 A/12 V = 24 W Rear lamp 0,2 A/12 V = 2,4 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | E01680-200 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlight 2A/12V = 24W Rear lamp 0,2A/12V = 2,4W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74104-100 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlight 2A/12V = 24W Rear lamp 0,2A/12V = 2,4W |
| Protection against ingress (seal) | IP56 |
*6 x E08500 mounting bushes included
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | C91143-200 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 70 Nm |
| Maximum support | 320% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74099-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 70 Nm |
| Maximum support | 320% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
Blind plug for lighting connector on Brose magnesium motors
Brose S T and S-Mag Crankshaft Pulley Bearing PLB20124, for Brose motor designation ‘S’, ‘T’ and S-Mag.