High precision 0.2Nm torque driver for Brose drive belt tension
We have sourced a 0.2Nm torque driver to set the drive belt tension of the Brose motor. The torque bit will tighten the belt tensioner screw to exactly 0.2Nm and then it will start clicking and will not let you overtighten the screw.
This tool will fit ALL Brose motors.
4 in 1 press tool for Brose C, T, S and S-Mag
This is a solid stainless steel press tool designed to complete 4 of the more awkward press jobs that are encountered when overhauling a Brose motor.
1, Remove the right hand crankshaft bearing from the torque sensor.
2, Machined to be an exact fit to remove the drive pulley sprag bearing and race.
3, Used to set the exact depth of the crankshaft needle roller bearing once the extra seal has been fitted.
4, Machined to set the right hand crankshaft bearing at the exact depth on the torque sensor.
This bearing race will fit Brose C, T, TF, S & S-Mag 2.1 & 2.2.
The large drive belt pulley contains a one way sprag clutch bearing and its race. This can become worn or damaged by rust, bearing failure etc. It can also be damaged while trying to remove the bearing itself.
The sprag clutch bearing MUST have a smooth, clean surface and the correct grease or the bearing will fail.
Early Brose C, T, TF motors had no seal covering the right hand crankshaft bearing. This seal is extremely effective at stopping water and dirt entering the bearing and ultimately the motor.
This is also a direct replacement if your Brose S or S-Mag seal is missing, worn or damaged. (For 1.2, 1.3, 2.1 and 2.2 motors)
Once the seal has been fitted over the sprocket carrier it will be pushed down when the chainring spider is re-fitted.
This high quality laser cut gasket will fit Brose S-Mag 2.1 & 2.2 and fits between the motor and the drive belt cover.
Description
Blind plug for the connector for the gear sensor or display.
Brose C, T, S and S-Mag lockring / spider nut tool
This is a castellated tool to fit all Brose chainring spider nut / lockring nuts. The tool has a 3/8″ socket drive for your ratchet or Torque wrench.
Description
| Part Number | E22243-200 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 50 Nm |
| Maximum support | 280% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G61340-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 50 Nm |
| Maximum support | 280% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | C97272-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74102-100 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | E06855-200 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2 A/12 V = 24 W Rear lamp 0,2 A/12 V = 2,4 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74105-xxx |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2 A/12 V = 24 W Rear lamp 0,2 A/12 V = 2,4 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | E01680-200 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlight 2A/12V = 24W Rear lamp 0,2A/12V = 2,4W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | G74104-100 |
|---|---|
| Engine type | Brushless Internal Rotor |
| Weight | 2,900 g |
| Dimensions L/H/W | 198mm/137mm/99mm (Casing Width) 198mm/137mm/150mm (Axis width) |
| Nominal voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 90 Nm |
| Maximum support | 380% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlight 2A/12V = 24W Rear lamp 0,2A/12V = 2,4W |
| Protection against ingress (seal) | IP56 |
*6 x E08500 mounting bushes included
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.
Description
| Part Number | C91143-200 |
|---|---|
| Mid-engine type | Brushless Internal Rotor |
| Weight | 3,400 g |
| Dimensions L/H/W | 213mm/128mm/98mm (Casing Width) 213mm/128mm/150mm (Axis width) |
| Nominal Voltage | 36 V |
| Continuous Rated Power | 250 W |
| Torque | 70 Nm |
| Maximum support | 320% |
| Support up to | 25 km/h |
| Walking support up to | 6 km/h |
| Light source | Headlamp 2,4 A/6 V = 14,4 W Rear lamp 0,1 A/6 V = 0,6 W |
| Protection against ingress (seal) | IP56 |
Please note the following important information:
Please contact us to discuss the software application required for your bike manufacturer (Specialized, Fantic, BMW, etc.)
All motors purchased from us have the option to be upgraded for enhanced resistance to water ingress and longevity. Please contact us for further details.